 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SCA3000-D02 Data Sheet SCA3000-D02 3-AXIS LOW POWER ACCELEROMETER WITH DIGITAL I2C INTERFACE Features * * * * * * * 2.35 V - 3.6 V supply voltage, 1.7 V - 3.6 V digital I/O voltage 2 g measurement range I2C digital interface: V2.1 compliant, 10-bit addressing, supports standard mode and fast mode Selectable frequency response Very low current consumption (2.5 V, 650 A typ) Temperature output 64 samples/axis buffer memory for output acceleration data and advanced features enable significant power and resource savings at system level Interrupt signal triggered by motion and free fall Size 7x7x1.8 mm Proven capacitive 3D-MEMS technology High shock durability RoHS compliant / lead free soldering Applications SCA3000-D02 is targeted to battery operated devices. Typical applications are but not limited * Motion activated functions in mobile terminals and antitheft systems * Inertial navigation * Inclination sensing in digital inclinometers * Tilt compensation in electronic compass * * * * * C/V Analog calibration & ADC DEMUX 1:3 Low-pass Filter Low-pass Filter Low-pass Filter Decimation Decimation Coordinate Mapping and Calibration SCL I2C i/f SDA Decimation Oscillator & clock Reference NonVolatile Memory Temperature sensor Motion detector Free fall detector Ring Buffer Control & INT INT Figure 1 SCA3000-D02 Block Diagram VTI Technologies Oy www.vti.fi PRELIMINARY - Subject to changes Doc.no.8255800A.01 1/4 Rev.A.01 SCA3000-D02 Performance Characteristics 1) Parameter Analog and digital Vdd Digital I/O Vdd Operating temperature ** Current consumption * Condition Typical supply range 2.35 - 2.7 V Min Typ 2) Max 2.35 1.7 -40 -2 -20 -1 36 56 200 2.5 1.8 / 2.5 <7 650 450 0.5 1333 0.01 1 3 45 70 3 5 250 256 1.8 35 35 300 2.7 2.7 85 Extended supply range 2.7 - 3.6 V Min Typ 2) Max -40 3.3 3.3 <9 800 550 2 50 0.5 1333 1 0.0 1 3 45 70 3 5 260 256 1.8 35 35 85 400 Units V V C A A A g mg mg/C Count/g % %/C % FS % Hz Hz mg RMS mg RMS Hz Count Count/C ms ms kHz Vdd Digital I/O Vdd Reset 3) Active Motion Detection mode Nominal Z-axis +1g position -40 ... +85 C -40 ... +85 C Acceleration range * 4) Offset calibration error * Offset temperature error ** 5) Sensitivity * 6) Sensitivity calibration error * Sensitivity temperature error ** 7) Non-Linearity ** 8) Cross-Axis sensitivity ** 9) Bandwidth ** 10) Noise ** 11) Output data rate ** Temperature output Turn on time ** 12) I2C clock rate ** * ** 1) 2) 3) 4) 2 20 +1 Measurement mode Bypass measurement mode Measurement mode Bypass measurement mode T=+23 C Sensitivity Measurement mode Bypass measurement mode 54 84 - 400 100% tested in production Qualified during product validation The product is factory calibrated at 2.5 V in room temperature. Typical values are not guaranteed. Includes the current through the internal 400 k pull-up resistor connected to digital I/O Vdd. Range defined as x2+ y 2+ z 2 2 g . The measuring range is tested on sensing element level. FS = 2g. Offset temperature error = {Count(0g)-Offset} / Sensitivity [ g ]. Sensitivity = Calibrated sensitivity. Offset= Calibrated offset. Sensitivity = {Count(+1g) - Count(-1g)}/2 [Count/g]. Sensitivity temperature error = {[Count(+1g)-Count(-1g)]/2 - Sensitivity} / Sensitivity x 100% [%]. Sensitivity = Calibrated sensitivity. From straight line through sensitivity calibration (+1g, -1g) points. The cross-axis sensitivity determines how much acceleration, perpendicular to the measuring axis, couples to the output. The total cross-axis sensitivity is the geometric sum of the sensitivities of the two axes which are perpendicular to the measuring axis. The angular alignment error between X, Y and Z axis is included into the cross axis sensitivity. Frequency responses according to Figure 3 and Figure 4. Average noise/axis over the measurement bandwidth defined as 1 (n 2 + n 2 + n 2 ) , where nx, ny and nz are 3 x y z 5) 6) 7) 8) 9) 10) 11) 12) the measured signal's standard deviation due to noise in x, y and z directions. Settling error less than 1% of FS. VTI Technologies Oy www.vti.fi PRELIMINARY - Subject to changes Doc. Nr. 8255800A.01 2/4 Rev.A.01 SCA3000-D02 Z X Y Figure 2 Sensing directions and package dimensions in mm with 50 m tolerance. Figure 3 Frequency response of SCA3000-D02 in measurement mode Figure 4 Frequency response of SCA3000-D02 in bypass measurement mode VTI Technologies Oy www.vti.fi PRELIMINARY - Subject to changes Doc. Nr. 8255800A.01 3/4 Rev.A.01 SCA3000-D02 Figure 5 Application schematic Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Name NC XRESET INT CLK DVSS DVDD DVIO CSB NC NC SCK_SCL MISO_SDA MOSI AVDD AVSS AVSS ATSTIO NC Function Not connected External reset, active low Interrupt output Digital ground Digital ground Digital supply Digital I/O supply Not connected Not connected Not connected I2C clock (SCL) I2C data (SDA) Not connected Analog supply Analog ground Analog ground Not connected Not connected Table 1 Pin descriptions Document Change Control Rev. A A.01 Date 21-Apr-06 13-Jun-06 Change Description 1st official release Dimensions updated VTI Technologies Oy www.vti.fi PRELIMINARY - Subject to changes Doc. Nr. 8255800A.01 4/4 Rev.A.01 |
Price & Availability of SCA3000-D02
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |